Page 1 of 7 123 ... LastLast
Results 1 to 10 of 62

Thread: Pipes jets filters etc

  1. #1
    Join Date
    Jun 2005
    Location
    Farnborough Hants
    Posts
    8,954

    Pipes jets filters etc

    An idea from the old board that didn't seem to carry over, to save people searching the whole site for peoples mods and to save a load of needless dyno time, perhaps people can list thier mods in a standard format to help others with a similar setup or who are thinking of some mods.


    1. Model 11/12
    2.full system / make
    3.can only/ make
    4. stage 1 or 3
    5.jet size
    6..needle clip position from top
    7.pilot screw setting .
    8.cams fitted
    9.Airbox mods
    10.BHP figure
    TPB-Founder member HCW
    Champagne ideas on beer money

  2. #2

    Re: Pipes jets filters etc

    1. 1109 (purgerex1)
    2.full system / Akra Supersports
    3.Not applicable
    4. 5. 6. 7.
    Keihin FCR 39 flatslide carbs (main jets as below, OCEMP needles 5th clip, 200 main air jets, 2.5 pilot air jet, mixture 1 turn)
    152.67 bhp 82.14ft-lbs Dyno Chart (With dual K&N pods and 145 main jets)
    151.9 bhp 82.23ft-lbs (with FCR 25mm red stacks and 155 main jets)
    150.5 bhp 81.17ft-lbs (with FCR 25mm red stracks and 155 main jets and Ramair socks fitted)
    Dyno charts

    8.ZZR cams fitted, 105IN/100EX
    9.No airbox
    10.152.7 BHP, 82ft-lbs

    Last edited by Purge; 9th March 2008 at 05:33 PM.
    Team Phat Bastid (Euro Division)
    HCW Founding Member...and they fucking love it!

  3. #3

    Re: Pipes jets filters etc

    1. 1224 (purgerex2)
    2.full system / Akra Supersports
    3.Not applicable
    4. stage 3
    5.6.7.
    160.4bhp, 95.6ft-lbs Dyno chart HERE
    Mikuni Yoshimura TMR MJN 38mm flatslide carbs (135 mains, 27.5 PJet, mix screws 1.25)
    8.ZZR cams
    9.No airbox
    10. 160.4bhp, 95.6 ft-lbs

    Last edited by Purge; 9th March 2008 at 05:40 PM.
    Team Phat Bastid (Euro Division)
    HCW Founding Member...and they fucking love it!

  4. #4
    Join Date
    Oct 2005
    Location
    Telford
    Posts
    909

    Re: Pipes jets filters etc

    1. 1200R
    2.Full System/ AKRA Supersports
    3.n/a
    4.Factroy pro 2.5 kit
    5.130 outside carbs and 132 on inside carbs
    6.FP needles 3rd groove down
    7.pilot screw 2 turns out
    8.standard cams
    9.junked snorkel replaced large K&N
    10.127.1 bhp at rear wheel (132.2 with baffle out)@8700rpm.
    11.83.4 ft-lbs
    Gabba Gabba Hey!
    wish i didn't know now what i didn't know then!

  5. #5
    Join Date
    Apr 2006
    Location
    Florida
    Posts
    15

    Re: Pipes jets filters etc

    1. Model 2001 1200R
    2. full system / Brock's Meg
    3. 41mm FCR's
    4. 158 mains
    5. EMR needles, center clip
    6. 45 pilots
    7. pilot screw setting 1 1/2
    8. Yosh cams, 81mm bore, 4mm stroke = 1307cc
    9. Open stacks
    10. 179.28hp & 101.13ft-lbs SAE
    Last edited by SteddyTeddy; 19th June 2009 at 02:05 PM. Reason: New dyno run 5/1/09

  6. #6
    Hawk1 Visitor

    Re: Pipes jets filters etc

    1. 1200S,
    2. Full S/S System/ MTC,
    3. n/a,
    4. Ivanīs,
    5. 112,
    6. 3rd groove from top,
    7. pilot screw 3 turns out,
    8. standard cams,
    9. junked snorkel / airbox mod,
    10. BHP figure 127hp at the rear & 80-82 ft-lbs.
    __________________

    Hawk1

  7. #7
    Join Date
    Jul 2005
    Location
    Madrid, Spain
    Posts
    330

    Re: Pipes jets filters etc

    1. 1200-s
    2. full akra
    3. n/a
    4. stage 2 (?)
    5. 104
    6. 4th groove
    7. 1 & 3/4
    8. standard cams
    9. junked snorkel
    10. haven't tested yet!

    Dani
    Kawasaki. LetTheGoodTimesRoll...
    DANI
    Blue 1200-s

  8. #8
    Join Date
    Mar 2006
    Location
    Atlanta, Georgia, USA
    Posts
    123

    Re: Pipes jets filters etc

    1. 2001 1200R
    2.Muzzy full stainless / chrome muffler
    3.N/A
    4. stage 3
    5.Unknown
    6..Unknown
    7.Unknown - Above three are Muzzy recommended setup for the Muzzy jet kit for the Muzzy ZRX-1200 1224 Big Bore setup with included K&N filter.
    8.Muzzy Cams
    9.Airbox - stock, minus snorkel, and holes cut in rear cover with K&N filter
    10.151.4 BHP 95 ft lbs torque

    Above is the Muzzys 1224 full setup installed and dyno'd by Muzzy's; that is why I don't have all the settings. I'll call Muzzy and see what settings they typically use and amend post. Might help guys that are doing a 1224 setup with Ross or other similar pistons.

  9. #9
    Join Date
    Jul 2005
    Location
    Hartshill, Warwickshire
    Posts
    1,285

    Re: Pipes jets filters etc

    1. 1200S (fairing removed)
    2. MTC system with custom twin outlet can
    3. N/A
    4. stage 3
    5. 130
    6. 4th
    8. Standard
    9. Junked, K&N Pods
    10. 132.3 atw

    The BHP figure is lower than I got in Holland with the airbox and single K&N. This may be due to differences in Dyno, so I'm going to pop her down to PDQ at some point soon to get a definitive (and trusted) test done.
    Last edited by via_macniven; 24th May 2006 at 03:14 PM.


    "Beauty is just a light switch away..."

  10. #10
    Join Date
    Jun 2005
    Location
    nowhere near you soon
    Posts
    3,972

    Re: Pipes jets filters etc

    1. 1100R C4
    2. full system / akra supersports with carbon oval
    3. NA
    4. Stage 3
    5. DJ 132 mains
    6. DJ needles 4th clip down
    7. dunno
    8. ZZR1100D cams
    9. K&N Pods
    10. 135.61bhp 77.14 ft lbs torque


    set up at PDQ





    TPB (ED)

Page 1 of 7 123 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Green Web Hosting! This site hosted by DreamHost.

Click here to order your ZRXOC Merchandise